The Apollo Abort Guidance System (AGS) was a backup computer system providing an abort capability in the event of failure of the Lunar Module's primary guidance system (Apollo PGNCS) during descent, ascent or rendezvous. As an abort system, it did not support guidance for a lunar landing.
The AGS was designed by TRW independently of the development of the Apollo Guidance Computer and PGNCS.
It was the first navigation system to use a strapdown Inertial Measurement Unit rather than a gimbaled gyrostabilized IMU (as used by PGNCS).[1] Although not as accurate as the gimbaled IMU, it provided satisfactory accuracy with the help of optical telescope and rendezvous radar. It was also lighter and smaller in size.
Contents |
The Abort Guidance System included the following components:[2]
The computer used was MARCO 4418 (MARCO stands for Man Rated Computer) whose dimensions were 5 by 8 by 23,75 inches (12,7 by 20,3 by 60,33 centimeters); it weighed 32,7 pounds (14,83 kg and required 90 watts of power. Because the memory had a serial access it was slower than AGC, although some operations on AEA were performed as fast or faster than on AGC.
The computer had the following characteristics:
The AEA has the following registers:[3]
Other less important registers are:
The AEA instruction format consisted of 5-bit instruction code, index bit and a 12-bit address.
The computer had 27 instructions:
ADD
: The contents of memory location are added to Accumulator A. The contents of the memory location remain unchanged.
ADZ
(Add and Zero): The contents of memory are added to Accumulator A. The contents of memory are set to zero.
SUB
(Subtract): The contents of memory are subtracted from Accumulator A. The contents of memory remain unchanged.
SUZ
(Subtract and Zero): The contents of memory are subtracted from Accumulator A. The contents of memory are set to zero.
MPY
(Multiply): The contents of Accumulator A are multiplied by the contents of memory. The most significant part of the product is placed in the Accumulator A, the least significant part is placed in Register Q.
MPR
(Multiply and Round): Identical to MPY
instruction, the most significant part of the product in Accumulator A is rounded by adding one to the contents of Accumulator A if bit 1 of Q Register equals one.
MPZ
(Multiply and Zero): Identical to MPR
instruction, the contents of memory are set to zero.
DVP
(Divide): The contents of Accumulator A and Register Q that form a dividend are divided by the contents of memory. The quotient is placed in Accumulator A and rounded unless the roundind would cause overflow.
COM
(Complement Accumulator): The contents of Accumulator A are replaced with their two's complement. If the contents of the Accumulator A are positive, zero or minus one, the contents remain unchanged.
CLA
(Clear and Add): The Accumulator A is loaded from memory. The contents of memory remain unchanged.
CLZ
(Clear, Add and Zero): Similar to CLA
instruction; the contents of memory are set to zero.
LDQ
(Load Q Register): The Q Register is loaded with contents of memory. The contents of memory remain unchanged.
STO
(Store Accumulator): The contents of Accumulator A are stored in memory. The contents of Accumulator A remain unchanged.
STQ
(Store Q Register): The contents of Q Register are stored in memory. The contents of Q Register remain unchanged.
ALS N
(Arithmetic Left Shift): The contents of Accumulator A are shifted left N places.
LLS N
(Long Left Shift): The contents of Accumulator A and bits 1 - 17 of Q Register are shifted left as one register N places. The sign of Q Register is made to agree with sign of Accumulator A.
LRS N
(Long Right Shift): Similar to LLS
, but the contents are shifted right N places.
TRA
(Transfer): The next instruction is taken from memory.
TSQ
(Transfer and Set Q): The contents of the Q Register are replaced with an address field set to one greater than the location of the TSQ
instruction. Next instruction is taken from memory.
TMI
(Transfer on Minus Accumulator): The next instruction is taken from memory if the contents of the Accumulator A are negative. Otherwise the next instruction is taken in sequence.
TOV
(Transfer on Overflow): If the overflow indicator is set, the next instruction is taken from memory.
AXT N
(Address to Index): The Index Register is set to N.
TIX
(Test Index and Transfer): If the Index Register is positive, it is decremented by one and the next instruction is taken from memory.
DLY
(Delay): Execution stops until a timing signal is received. The next instruction is taken from memory.
INP
(Input): The contents of input register specified by address are placed in Accumulator A. The input register is either set to zero or remains unchanged (depending upon the selected register).
OUT
(Output): The contents of the Accumulator A are placed in output register specified by address.
First design ideas of the Abort Guidance System did not include the use of the computer but rather a sequencer without any navigation capability. This would be adequate to put the Lunar Module to the lunar orbit where the crew would wait for rescue by the Apollo CSM. Later design included a digital computer to provide some autonomy.[1]
The AGS software was written in LEMAP assembly language that uses 27 instructions described above and a set of pseudo-operations used by the assembler.
The main computation cycle was 2 seconds long. This 2-second cycle was divided into 100 segments; each of these segments had a duration of 20 ms. These segments were used for computations that needed to be recalculated every 20 ms (like IMU signal processing, update of PGNCS downlink data, direction cosines update, etc.).
There was also a set of computations that had to be performed every 40 ms (engine commands, external signal sampling, attitude control, etc.).
Other computations were performed every 2 seconds and these equations were divided into smaller groups so they could be recalculated during the remaining (i.e. unused) time of 20 ms segments (e.g. radar data processing, calculation of orbital parameters, computation of rendezvous sequence, calibration of IMU sensors, etc.)[4]
The software for AGS was reviewed many times to find program errors and to reduce the size of the software. There are some known versions of the software that were used for unmanned and manned tests.[5]
The AGS User interface unit was named DEDA (Data Entry and Display Assembly). Its function was entry and readout of data from the AGS. Some of the system's functionality was built into DEDA unlike the DSKY used by AGC.
DEDA had the following elements:
There are few actual descriptions of the use of the AGS, as a landing abort was never needed during the Apollo missions. There were, however, two cases in which the AGS was used.
Its first (and intended) use was during the Apollo 10 mission, following the separation of the Lunar Module descent stage, prior to the ascent stage burn. An incorrect switch setting[6] led to the AGS causing extensive oscillations of the ascent stage.
The next use of the AGS was during the lunar ascent phase of the Apollo 11 mission, when the LM crew performed a sequence of rendezvous maneuvers that resulted in gimbal lock; the AGS was subsequently used to acquire attitude control.[2]
|